The DFW Handyman®Honest Craftsmanship.

Repairs around the house

What should you check before buying a new light fixture?

Four checks before you buy: fixture weight against the box, canopy size, dimmer compatibility and how it hangs. Also why the install itself is licensed electrical work.

Your local expert

Hands-on since 1999 · About Daniel

The new fixture on the brick

The new fixture on the brick. From exterior lights replaced and a door sill repaired, one of Daniel’s projects.

Short answerCheck four things before you buy: the fixture’s weight against what the ceiling box can hold, whether its canopy covers the old fixture’s footprint, whether it works with your dimmer, and how it will hang in the space. Replacing a fixture is electrical work, which Texas licenses even in the same spot, so ask whoever you hire who does the electrical part and whether they are licensed. A light in a new location, or a new switch, also means new wiring.

Key takeaways

  • A heavier fixture may need a stronger box or brace than the old one had.
  • A canopy smaller than the old one can leave an unpainted ring on the ceiling.
  • LED fixtures need a dimmer listed as compatible, or they may flicker and hum.
  • Replacing a fixture is electrical work in Texas, even in the same spot; a new spot or new switch also needs new wiring.
In this guide
  1. Weigh the fixture against the box
  2. Measure the space and the ceiling
  3. Dimmers, smart switches and bulbs
  4. Chandeliers and tall entries
  5. Same spot or new spot
  6. What to send before the visit

Weigh the fixture against the box

Every fixture lists its weight on the spec sheet or the box. Ceiling boxes have limits too, and many are marked inside with the maximum fixture weight they are rated for. A small flush light weighs very little. A chandelier, a large drum pendant or a glass fixture can weigh many times more than what was there before, and an older ceiling box held up by a single nail was never meant for that.

If the new fixture is heavier than the old one, plan on checking the box and its fastening before installation day. A heavy fixture may need a box screwed directly to a joist or a brace that spans the joists. That is ordinary preparation, but it changes what parts need to be on hand.

Measure the space and the ceiling

Look at the canopy, the round or square plate that sits against the ceiling. When an old fixture comes down, it often leaves a ring of older paint, or a hole larger than the box. A new canopy that is smaller than the old one will show it. Either choose a canopy at least as large, or plan a ceiling touch-up.

Then think about how the fixture hangs. Over a dining table, lighting designers commonly suggest the bottom of a chandelier sit about 30 to 36 inches above the tabletop. In an entry or hallway, the fixture has to clear the tallest person in the house and the swing of any door. Most chains and rods can be shortened during installation, so buy one that can reach the height you want and trim from there.

  • Ceiling height at the fixture location.
  • Width of the old canopy and any paint ring around it.
  • Table size and position, for a dining fixture.
  • Door swing and walkway clearance, for an entry or hall.
The finished powder room
The finished powder room. From bathroom vanity light and mirror, one of Daniel’s projects.

Dimmers, smart switches and bulbs

Many new fixtures have built-in LEDs. LED lights and older dimmers designed for incandescent bulbs often do not get along: the light flickers, hums or will not dim smoothly. Fixture makers publish lists of dimmers they have tested. If yours is not on it, plan to replace the dimmer along with the fixture.

Smart switches add one more question. Many need a neutral wire in the switch box, and older homes sometimes do not have one there. Check the switch maker's requirements before you buy, and send a photo of the existing switch with its cover plate off only if you are comfortable switching off the breaker first.

Finally, match the color of the light. Bulbs and LED fixtures are rated in kelvin; lower numbers look warmer. Mixing very different ratings in one room is the most common reason a new fixture looks wrong.

Choosing a new light fixture? Tell Daniel about it

Chandeliers and tall entries

A chandelier in a two-story entry is a two-person job. Crystals and arms are usually assembled on a padded floor first, then the fixture is lifted and supported while the wires are connected, never left hanging by its wires. Expect a tall ladder or scaffold, floor protection, and time to level the fixture so it hangs straight from the angles people see it from. Before it goes up, decide how bulbs will be changed later; some people ask for the fixture to hang a little lower than first planned so it can be cleaned from a standard ladder.

Same spot or new spot

Replacing a fixture where one already hangs, on its existing switch, is the simplest version of the job, but it is still electrical work, which Texas licenses, and the law has no small-job exception for someone you hire. A light where there is none today, an added switch, recessed lights cut into a ceiling, or a new circuit all need new wiring on top of that, and that belongs to a licensed electrician. So does any box with brittle or scorched insulation, aluminum wiring, or a breaker that keeps tripping. Some cities also require permits for electrical work, so check with your city’s building department; whether a permit is needed is a separate question from who may do the work. If we find any of this during a visit, we’ll tell you, and help you find the right licensed pro.

What to send before the visit

Send The DFW Handyman the product link or spec sheet, a photo of the current fixture and its switch, the ceiling height, and whether the switch is a dimmer, through request service. With that, Daniel can tell you ahead of time whether the box needs work, whether the dimmer will cooperate, and whether a second person or scaffold is needed. We’ll also tell you how the electrical part is handled on your job.

Frequently asked questions

Can I reuse the existing wiring for a different fixture?
In the same spot, usually yes, provided the wiring is in good condition, the box is secure and rated for the new fixture's weight, and the connections are made fresh. LED fixtures draw less power than the old bulbs did, so a like-for-like replacement rarely asks more of the circuit. What cannot be reused is wiring that is cracked, scorched or too short to reach safely.
Do I need an electrician to replace a light fixture in Texas?
Texas licenses electrical work, and the law makes no small-job exception for replacing a light fixture for a customer, even on the existing box and switch. If you own the home and live in it, Texas lets you do some electrical work on it yourself, though city rules and permits can still apply. If you hire someone, ask who will do the electrical part and whether they are licensed. Adding wiring, a switch, a circuit or a new location is a job for a licensed electrician in any case.
How do I change bulbs in a fixture I cannot reach?
For ceilings a little out of reach, a bulb changer on an extension pole works for many bulb shapes. For a chandelier or floodlight high in an entry or vaulted room, it is safer to have someone come with the right ladder or scaffold. If you are replacing the fixture anyway, long-life LED bulbs or integrated LEDs reduce how often anyone has to go up.
Daniel Myers, founder of The DFW Handyman

Ask Daniel

Choosing a new light fixture?

Tell Daniel what you need and he'll explain how it's handled. Send the fixture link and a photo.