Key takeaways
- Match the mount to the TV weight and the hole pattern on its back.
- Drywall mounts go into studs; brick and stone use rated masonry anchors.
- Over a fireplace, heat and neck strain are the two questions to settle.
- A regular power cord is not rated to run inside a wall.
In this guide
Start with the TV and the mount
Two numbers on the TV decide which mount fits: its weight and the spacing of the threaded holes on its back, called the VESA pattern. The mount should be rated for both, with room to spare. A fixed or tilting mount holds the TV close to the wall. A full-motion arm lets it swing out, which puts much more leverage on the fasteners, so it asks more of the wall behind it.
Decide the type of mount before the visit, and buy it to match the TV you have, not the next one.
Drywall: find the studs
In most homes, wood studs sit behind the drywall at regular intervals, commonly 16 inches apart. The mount's wall plate is fastened into at least two of them with the lag bolts it comes with. Plastic drywall anchors and hollow-wall anchors are not for TVs; drywall alone can tear out under a heavy screen, especially one that is pulled out on an arm.
If the studs do not line up with where you want the TV, a mount with a wider wall plate, or one that lets the TV slide sideways on its rail, usually solves it. Some homes and many condos have steel studs, which need different hardware. A stud finder, a small test hole, or a strong magnet on the screws tells which you have.
Brick and stone
Solid brick holds a mount well when it is drilled with a hammer drill and fastened with sleeve anchors, wedge anchors or masonry screws rated for the weight. Many installers anchor into the face of the brick rather than the mortar joint because brick is usually stronger, but the condition of both matters; soft or crumbling mortar is a warning sign.
Stone is less predictable. A thin stone veneer glued to a wall is not the same as solid stone, and it may not carry a TV by itself; the mount may need to reach the structure behind it. Holes in masonry are permanent, so place a paper template of the TV and decide on height before anyone drills.
Have a TV to mount? Tell Daniel about it
Over a fireplace: heat and height
Heat is the first question. TV makers list an operating temperature range, and heat damage may not be covered by the TV warranty. Run the fireplace for a while and hold your hand flat on the wall where the TV would go. If it is too warm to keep it there comfortably, it is too warm for the TV. A deep mantel helps by turning rising heat away from the wall.
Height is the second. A TV over a fireplace sits higher than eye level, and looking up for a whole movie strains the neck. Tape a paper template on the wall and sit in your usual seat for a few evenings before deciding. Pull-down mounts that lower the screen when in use are one answer for a tall mantel.
Hiding the wires the right way
Low-voltage cables, such as HDMI, speaker and network cables, can run inside the wall when they are rated for in-wall use. The power cord is different. An ordinary power cord is not rated to run inside a wall. The two safe options are a recessed in-wall power kit made for this purpose, which carries power behind the wall through rated components, or a licensed electrician adding an outlet behind the TV.
Walls are not always empty. A chimney chase, a fire block or a horizontal brace between studs can block a cable path. Where that happens, a slim paintable raceway on the surface is a clean alternative.
- Where will the cable box, game console or receiver live?
- Where is the nearest outlet today?
- Do you want a soundbar below the TV?
- Is the wall drywall, brick, stone or plaster?
Getting ready for the install
Send The DFW Handyman the TV model, the mount you bought (or want help choosing), a photo of the wall from your seat, and the answers to the list above, through request service. Daniel brings a laser level and floor protection, and can tell you in advance whether the power needs an electrician. More on the work itself is on the TV mounting page.

