Key takeaways
- Measure the window depth first: it decides inside or outside mount, and whether the shade you like will fit.
- Heavy drapery rods need a center support and screws into framing or anchors made for the wall.
- Tall windows and ceiling tracks come down to safe access and finding solid wood overhead.
- A broken bracket can usually be replaced on its own once you know who made the blind.
- Doing every room in one visit keeps rod heights and lines consistent through the house.
In this guide
Inside mount or outside mount: measure before you buy
An inside mount sits within the window opening. It looks tidy and shows off the trim, but it needs enough depth for the headrail and an opening that is close to square. An outside mount goes on the trim or the wall above the window. It covers an out-of-square opening, blocks more light at the edges, and can make a window look larger.
Measure the width at the top, middle and bottom, and the height on both sides. In older houses those numbers often differ, and the smallest one decides an inside mount. Check the depth, and look for anything a blind could hit: window cranks, lock handles, alarm sensors on the sash. If the blinds or shades are being custom ordered, follow the maker’s measuring instructions exactly, and agree up front who is responsible for the measurements.
What actually holds them up
Blinds and shades hang from small brackets, and the brackets are only as good as what their screws bite into. Inside-mount brackets screw up into the wood at the top of the window opening. Outside-mount brackets hold most securely in the framing above the window, called the header, which is solid wood in most walls. Light blinds can go into drywall with the right anchors; heavy wood blinds and large shades should not rely on drywall alone.
Drapery rods carry more weight than they look, and every time a heavy lined panel is pulled open, it tugs on the brackets. A long rod needs a center support bracket at the spacing the rod maker gives, or it sags in the middle. The end brackets go into framing wherever possible, and into anchors rated for the load where it isn’t.
Plaster walls can carry heavy drapery rods well, but they crack if drilled carelessly. The method is the same as for heavy art: slow pilot holes, tape over the spot, and fasteners made for plaster. How to hang heavy art and mirrors explains it. Brick or stone around a window needs masonry anchors set in drilled holes, ideally in the mortar joints, which are easier to patch later.
Tall windows, two-story rooms and ceiling tracks
A tall window or a two-story room mostly changes how the work is reached. A long shade is heavy and awkward to lift and level from a ladder, stairs need a ladder that sits safely on uneven steps, and the highest windows may need scaffolding. Ask how anyone you hire plans to reach the top before the day of the install.
Think about how a tall shade will be raised and lowered. Cordless lift, a wand, or a motorized shade avoids long cords. Battery and rechargeable motors need no wiring. A shade motor wired into the house needs power at the window, which means new wiring; that belongs with a licensed electrician, so plan it before the walls are painted, and we’ll tell you, and help you find the right licensed pro.
Ceiling-mounted curtain tracks are popular in rooms with tall ceilings, and they need solid wood above them. The screws should land in ceiling joists or in blocking between them. If the joists run the same direction as the track, a painted mounting board fastened across several joists gives every bracket something solid. A laser level keeps a long track straight, though in some rooms it looks better to follow a ceiling that isn’t perfectly level, so that the gap stays even. That is a choice worth making together on site.
Blinds or curtain rods to put up? Tell Daniel about it
Several rooms in one visit
Putting up rods and blinds through a whole floor is a good one-visit job when it is planned. Make a simple list: each window by room, its size, inside or outside mount, and what is going up. Have the products delivered before the visit and check that each box has its brackets and screws. Missing hardware is the most common reason an install stops halfway.
Doing the rooms together also keeps the house consistent. Rods in the same room should sit at the same height, and the line should carry from room to room where windows can be seen together. Mention whether old brackets and rods need to come down and the holes patched. If there are small children in the house, ask for cord tie-downs on corded blinds, or choose cordless; babyproofing a home covers that in more detail.
A broken bracket, or a blind that keeps falling
A cracked bracket or a lost valance clip rarely means a new blind. Look for the maker’s label on the headrail, usually on the top or one end, and order the matching bracket from them. Generic brackets fit many blinds but not all.
If a blind keeps falling down, the bracket is usually the symptom. The common causes are screws that only reached drywall, screw holes that have stripped, or brackets set out of line so the headrail is forced in and pops out. The fix is to move the bracket slightly to solid material, or fill the stripped holes and fasten into sound wood, and to line the brackets up so the headrail snaps in without force.
Who installs blinds in Dallas, and what to send
Blinds and window treatments are part of the everyday work The DFW Handyman does across Dallas and the rest of our service area, alongside picture hanging and other small installs listed under everyday projects.
To plan the visit, send your window list, a photo of each window type with the trim in view, the ceiling height for any tall windows or tracks, and links to the products. Note whether the walls are plaster or brick. Start with Request service, and we’ll tell you what the install involves and anything to check before you order.
