Key takeaways
- One damaged plank can be cut out and a new one woven in without lifting the floor around it.
- Matching an older floor means matching species, width, thickness and cut, then blending the color.
- After a leak, stop the water and let the floor dry before deciding what to replace.
- A soft spot is a subfloor or framing question, not a flooring one, and is worth checking soon.
- Light scratches in engineered flooring can be filled or blended; deep ones usually mean replacing the plank.
In this guide
Replacing one plank, or a few loose boards
A single damaged plank doesn’t mean a new floor. Because wood boards lock together with tongues and grooves, the damaged board is cut out down its middle and removed in pieces, so the boards around it are not disturbed. The new board is trimmed to drop into place, fastened or glued, and finished to blend. The same method works for a few boards in a row.
Loose floorboards in a hallway usually mean the original nails or glue have let go. They can be refastened into the subfloor or joists from above with small finish fasteners that are set and filled, or, in a house with a crawl space, sometimes from below where nothing shows. Hardwood floor repair and installation is part of our carpentry work.
Matching new boards to an older floor
An older wood floor can be matched, but it takes care. The new boards need the same species, width and thickness, and ideally the same cut of the grain. Older floors are often a width or thickness that is no longer standard, so boards may need to be milled to fit.
Color is the harder part. Wood darkens and ambers with age and light, so a new board looks different even in the same species. The best match often comes from boards borrowed from a closet or under an appliance, with the new wood placed in that hidden spot instead. Stain and finish can blend a small repair well. When a large area is replaced, refinishing the whole room together is what makes the repair disappear.
Water damage: repair or replace
After a leak from a refrigerator line, a dishwasher or a sink, the first step is to stop the water and dry the floor and the space under it. Wood that has absorbed water cups, with board edges higher than the centers. Cupping often settles back as the wood dries, so judging the floor too early can mean replacing boards that would have recovered. A moisture meter shows when the floor and subfloor are back to normal.
Boards are worth replacing when they stay cupped or crowned after drying, turn black, split, or come apart, which is common with engineered flooring whose layers separate. If the subfloor is soft or there is mold under the floor, that comes first. A leak from a refrigerator ice maker line is often a fitting or a supply line, and a leak in a wall or under the slab is a bigger plumbing job. Either way the plumbing repair, which Texas licenses, comes before any floor repair. Small bathroom repairs explains which repairs count as plumbing.
Damaged boards in a wood floor? Tell Daniel about it
Squeaks and soft spots
Squeaks come from boards rubbing against each other or against the nails that hold them. On a floor over a crawl space, a squeak can often be fixed from below by drawing the subfloor tight to the joist. From above, special screws that break off below the surface, or finish nails set into the joist, quiet most squeaks with a small filled hole. Floors on a concrete slab squeak for different reasons, usually boards that have come loose from the slab or the strips underneath. Homes across Dallas include both older pier-and-beam houses with crawl spaces and newer homes on slabs, and the right fix depends on which one you have.
A soft spot is more serious than a squeak. A floor that gives or bounces in one spot can mean a subfloor that has been weakened by water, a joist that is cracked or undersized, or support underneath that has settled. Signs that it needs attention soon: a spot that is getting larger, a dip you can see, a nearby toilet, tub, dishwasher or exterior door, or a musty smell. If the framing or foundation is the cause, that is a structural repair for a foundation or structural contractor, and we’ll say so plainly.
Scratches, engineered floors and transition strips
Engineered wood flooring has a real wood top layer over a plywood or composite core. Light scratches in the finish can be blended with touch-up products matched to the floor’s color. Deeper gouges can be filled. Because the top layer can be thin, sanding a scratch out is risky; a deep scratch in a visible spot is often better fixed by replacing the plank. Pet damage repairs covers scratches from pets.
Transition strips between rooms, where wood meets tile, carpet or another floor, crack, loosen or get kicked out of their tracks. Replacing one is a common small repair. The right profile depends on the height difference between the two floors, so measure both sides or send a close photo.
Installing hardwood in one room
Hardwood floor installation is listed in our carpentry work, and one room is a manageable size. The questions that shape it: whether the floor will be nailed, glued or floating, what is underneath (a slab or a wood subfloor), how the new floor meets the rooms next to it, and whether doors will need trimming to clear it. Wood also needs time in the house to adjust to the indoor humidity before it is installed. For new trim and baseboards after the floor goes in, see trim, moulding and wall paneling.
Getting it looked at
Send photos of the damaged area up close and from a few feet back, a photo of a full board width with a tape measure across it, and a note on whether the house has a crawl space or sits on a slab. For water damage, say where the water came from and whether it has stopped.
Use Request service. We’ll tell you whether it looks like a plank repair, a subfloor problem, or something that needs a different trade first.
